ISO 9001:2008 Certified
TYPICAL PROPERTIES of Peek GF 30% (Compression Molded Glass Filled Polyetherether) |
|||
| ASTM or UL TEST | PROPERTY | Metric | English |
| PHYSICAL | |||
| ASTM D792 | Specific Gravity | 1.59 g/cc | 1.59 g/cc |
| Immersion; ASTM D570 | Water Absorption | 0.015% | 0.015% |
| Immersion; ASTM D570 | Water Absorption at Saturation | 0.050% | 0.050% |
| MECHANICAL | |||
| ASTM D638 | Tensile Strength (psi) | 51 MPa | 7400 psi |
| ASTM D638 | Tensile Strength at 150°C (300°F) | 6.89 MPa | 1000 |
| ASTM D638 | Tensile Strength at 65°C (150°F) | 34.5 MPa | 5000 psi |
| 10% Def.; ASTM D695 | Compressive Strength | 152 MPa | 22000 psi |
| ASTM D695 | Compressive Modulus | 3.45 GPa | 500 ksi |
| ASTM D638 | Elongation at Break | 1.0% | 1.0% |
| ASTM D638 | Tensile Modulus | 6.89 GPa | 1000 ksi |
| ASTM D790 | Flexural Strength | 82.7 MPa | 12000 psi |
| ASTM D790 | Flexural Modulus | 6.21 GPa | 900 ksi |
| ASTM D785 | Hardness, Rockwell M | 103 | 103 |
| ASTM D785 | Hardness, Rockwell R | 124 | 124 |
| ASTM D2240 | Hardness, Shore D | 88 | 88 |
| ASTM D256 Type A | IZOD Notched Impact (ft-lb/in) | 0.534 J/cm | 1.00 ftlb/in |
| Dry vs. Steel; PTM55007 | Shear Strength | 96.5 MPa | 14000 psi |
| 4:1 safety factor; PTM 55007 | Limiting PV (4:1 Safety Factor) (ft-lb-in2-min | 0.876 MPa-m/sec | 25000 psi-ft/min |
| PTM 55010 | Wear Factor “k” x 10-10(in3-min/ft-lb-hr | 302 x 10-8 mm³/N-M | 150 x 10-10 in³-min/ft-lb-hr |
| THERMAL | |||
| ASTM E831 | Coefficient of Linear Thermal Expansion (x 10-5 in./in./°F) |
25.2 µm/m-°C @Temperature -40.0 – 149 °C |
14.0 µm/m-°F @Temperature -40.0 – 300 °C |
| Crystalline, Peak; ASTM D3418 | Melting Point | 340°C | 644°F |
| ASTM F433 | Thermal Conductivity | 0.429 W/m-K | 2.98 BTU-in/hr-ft²-°F |
| Long Term | Maximum Service Temperature, Air | 249°C | 480°F |
| ASTM D648 | Deflection Temperature at 1.8 MPa (264 psi) | 232°C | 450°F |
| UL94 (1/8 in (Estimatred Rating | Flammability Rating | V-0 | V-0 |
| ELECTRICAL | |||
| Short Term; ASTM D149 | Dielectric Strength | 21.7 kV/mm | 550 kV/in |
| EOS/ESD S11.11 | Surface Resistivity per Square | >= 1.00e+13 ohm | >= 1.00e+13 ohm |
| Chemical Resistance Properties | |||
| – | Acids, Strong (pH 1-3) | Limited | Limited |
| – | Acids, Weak | Acceptable | Acceptable |
| – | Alcohols | Acceptable | Acceptable |
| – | Alkalies, Strong (pH 11-14) | Acceptable | Acceptable |
| – | Alkalies, Weak | Acceptable | Acceptable |
| – | Chlorinated Solvents | Acceptable | Acceptable |
| – | Conductive / Static Dissipative | No | No |
| – | Continuous Sunlight | Limited | Limited |
| – | Hot Water / Steam | Acceptable | Acceptable |
| – | Hydrocarbons – Aliphatic | Acceptable | Acceptable |
| – | Hydrocarbons – Aromatic | Acceptable | Acceptable |
| – | Inorganic Salt Solutions | Acceptable | Acceptable |
| – | Ketones, Esters | Acceptable | Acceptable |
NOTE: The information contained herein are typical values intended for reference and comparison purposes only. They should NOT be used as a basis for design specifications or quality control. Contact us for manufacturers’ complete material property datasheets.
Click edit button to change this text.